What power supply should i choose




















Prebuilt Gaming PCs. Budget Prebuilt PCs. RTX Desktops. Best Hz Monitors. Cheap Hz Monitors. Acer Gaming PCs. Samsung Gaming Monitors.

HP Gaming PCs. Acer Predator Monitors. MSI Gaming Monitors. Best Gaming Chairs. Best Gaming Desks. RTX Laptops. Best Gaming Monitors. Best Gaming Headsets. Best Gaming Routers. Ryzen 9 Laptops. Best Gaming Mics.

Ryzen 7 Laptops. Ryzen 5 Laptops. Wireless Gaming Mice. Budget Gaming Laptops. About Us. Privacy Policy. Terms of Service. Affiliate Disclaimer. Contact Us. Power supplies in the higher certification tiers tend to command very high prices, however. Average users with average needs should probably stick to the simple 80 Plus or the 80 Plus Bronze level unless they find a particularly juicy deal on a Silver or Gold PSU. In a single-rail design, all of the power from the supply will be available to any component connected to the unit, regardless of the connector or cable used.

In the event of a failure, however, a single-rail power supply has the potential to shoot much more current into your components. On the other hand, that disadvantage becomes a major advantage if you ever encounter a catastrophic failure. The OCP mechanisms in a multi-rail power supply monitor each rail and will shut the whole unit down if they detect an overload on any of the rails. The OCP on single-rail units kicks in only at much higher amperages, which could lead to a major melt-down if a serious overload occurs.

So which is better type of power supply is better—single-rail or multi-rail? Neither, usually. From a performance standpoint, both work equally well; and in general both are very safe to use. Another consideration is cabling. Power supplies are available with hard-wired cabling, with partially modular cabling, or with fully modular cabling.

In modular power supplies, you can add or remove cabling from the PSU as needed to avoid case clutter. Whenever you introduce an additional connection between the PSU and your components—as happens with modular power supplies—you add more resistance and another potential point of failure into the line; and any increase in resistance translates into lost efficiency.

That said, the additional resistance is normally minimal and not a cause for concern for most users. There are several different versions of the ATX12V form factor, and they can be very different from one another. The ATX12V v1. The ensuing ATX12V v1. A substantial change occurred in the ATX12V v2. Also, the ATX12V v2.

Later, the ATX12V v2. The EPS12V form factor was originally designed for entry-level servers, but more and more high-end desktop motherboards are featuring the 8-pin EPS12V processor power connector now, which enables users to opt for an EPS12V power supply. They are all smaller than the standard ATX12V form factor power supply in terms of physical size, and small form factor power supplies need to be installed in corresponding small form factor computer cases.

That means it needs to have all the required connector types. The first connector to consider is the main connector that powers the motherboard. This connector comes in two types, pin and pin. Just check to be sure. Next up is the processor power connector, which comes in 4-pin and 8-pin versions. As with the main power connector, many modern motherboards have switched to the larger format.

Again, make sure your power supply is compatible. The most frequently used power connector is the 4-pin Molex connector. That means they require fans to stay cool and run efficiently. If your PC operates in a quiet space, then larger fans that spin more slowly to move the same amount of air will likely result in a quieter PC.

This is one area where in-depth reviews will be particularly helpful, as they tend to measure how loud a power supply is during various levels of operation and so offer some guidance as to how loud you can expect your PC to run. Finally, there are three basic types of power supply cabling. Hard-wired cabling means that every connector is directly connected to the power supply and so will be present whether needed or not. Modular cabling means that each connector can be added in as needed.

That makes it easier to keep your case clean and uncluttered, but it also introduces some additional complexity — and price — and some additional resistance thanks to extra physical connections. Hybrid systems have some cables, such as the main power connect, physically connected and the others being optional. But spending a little time up-front to make sure your power supply provides your PC components with reliable, consistent, and safe power will save you huge amounts of time in the long term, and it will help make your PC a better and more efficient machine.

A good article on power supplies. I am facing this issue on a build of 6 years ago. I have a problem with boot up. Save my name, email, and website in this browser for the next time I comment. All rights reserved.



0コメント

  • 1000 / 1000